Page 1 of 2
Lost World Model 3 wiring
Posted: Wed Nov 15, 2006 4:42 pm
by OldFoo
Hello !
I could get a lost world model 3 pcb with guns, filterboard, gun pcb and the 12 sensor.
But the wiring loom is missing.
Does anybody have such a loom or know a merchant who sells it ?
I would like to run the pcb in my astro city cab (so i would make the wiring loom jamma compatible).
Greetings
RFK
Posted: Thu Nov 16, 2006 9:39 am
by OldFoo
The one on eBay?? haha yes I told the guy it is impossible to find the wiring looms, you'd have to make them.
Posted: Thu Nov 16, 2006 10:36 am
by OldFoo
Where is this auction?
Can't find it on the superb eBay search
Posted: Thu Nov 16, 2006 1:42 pm
by OldFoo
AndyGeezer wrote:The one on eBay?? haha yes I told the guy it is impossible to find the wiring looms, you'd have to make them.
Hi !
Ok, so do you have any information to make such a wiring loom ?
What about the 12 sensors around the monitor ?
Does it matter if my monitor is a little bit bigger (29 inch instead of the usual 25 inch) ?
What about the idea to buy a model 3 jamma loom (many merchants have them in stock) and modify it for the lost world pcb ?
And yes, it was an auction on ebay.co.uk.
Greetings
RFK
Posted: Thu Nov 16, 2006 4:01 pm
by OldFoo
You can download the Lost World manual.
http://www.suzo.co.uk/websites/suzo/mai ... MANUAL.pdf
It was a 29" monitor, not 25"
You can make the wiring, just need a lot of patience, and ideally you need to make the gun wiring looms RF shielded.
Posted: Thu Nov 16, 2006 5:41 pm
by OldFoo
Hello !
Thank you very much for the link.
So wish me luck with the wiring loom.
The game is so incredible. I remember the great crocodile jumping out of the water and attacking the players. Or the gigantic T Rex hunting down the players in a tech lab.
Or...and of course the shitting dino
...those were the days sega...those were the days my friend *sigh*
But ok, Virtua Fighter 5 and Afterburner Climax also rock.
Greetings
RFK
Posted: Thu Nov 16, 2006 8:12 pm
by OldFoo
If you like shooters, you should try Ghost Squad, that game rocks!
Posted: Thu Nov 16, 2006 10:31 pm
by OldFoo
Hi !
Thank you for the tip.
How much will a kit cost ?
And where can i get one ?
Greetings
RFK
Posted: Fri Nov 17, 2006 8:28 am
by OldFoo
The game is quite new, so you'd be looking in around ?4000 for the kit.
The Chihiro Type 3 mainboard is worth ?2000, as it can run games like Outrun 2 SP/Maximum Tune 1/2
Posted: Mon Nov 27, 2006 7:08 pm
by OldFoo
Hi again !
I have recieved the lost world kit and i have also printed out the lost world manual.
There are two sheets with the pinout information.
Voltage and rgb signal will be really no problem (i have made a wiring loom for house of the dead already, so im an not a noob
).
But now comes the different part: Could you explain how to wire up the guns and the sensor parts with the gun i/0 board and the model 3 filterboard ?
The gun i/o board also needs 12 and 5 volt if i am not wrong.
Greetings
RFK