THE MAZE OF THE KINGS

OldFoo · Post by **OldFoo** » Sun Mar 07, 2010 7:26 am

Hello everyone,

'm restoring a Maze of the Kings on cab Naomi Universal Upright

anyone have a pdf copy of the manual connection diagrams upright version? thanks :smt004

n.b. I need the wiring standard molex connection to the VTS, I noticed differences compared to the confidential mission :smt014

OldFoo · Post by **OldFoo** » Sun Mar 07, 2010 9:11 am

Have you got any pictures as a reference?

By the way: your english is improving, dude!

OldFoo · Post by **OldFoo** » Sun Mar 07, 2010 10:30 pm

I believe I have the original Manual for this, will need to check tomorrow, if I do have it, pay shipping and its yours

OldFoo · Post by **OldFoo** » Sun Mar 07, 2010 11:36 pm

just done a gun conversion on my cab what connector you stuck on.?

OldFoo · Post by **OldFoo** » Sun Mar 07, 2010 11:49 pm

In the process of doing the same, you will find the manual you need on the link below and a few others that you may need.

http://www.segaarcade.com/archive/mazeo ... spx#bottom

OldFoo · Post by **OldFoo** » Mon Mar 08, 2010 11:08 am

the only diffrence between confidencal mission and maze of kings was the guns as the pots on the gun board had to be ajusted as the sights of the guns were much higher than standard sega guns. theres a bulliten about it on sega service if memory servers me right.

when doing in my conversion i did notice that the pins from the led sensors to gun board were the wrong way around and i had to remove pins from housing and then put them the right way. as they were oposit ways around.

made a quick releace loom up from AMP connectors to gunboard. With andygeezers Help as he is the man when it comes to wiring.

AMP Connects Pinout

---------------------------------------------------------

White 12pin Amp

---------------

Pin 01 = Start (Wired up normally)

Pin 06 = Trigger (Pin 8 CN_OUT) Blue

Pin 07 = Screen Out (Pin 6 CN_OUT) Green

Pin 12 = GND (Wired up normally)

Yellow 12pin Amp

----------------

Pin 01 = Start (Wired up normally)

Pin 06 = Trigger (Pin 9 CN_OUT) Blue/White

Pin 07 = Screen Out (Pin 7 CN_OUT) Green/White

Pin 12 = GND (Wired up normally)

White 8pin Amp

--------------

Pin 08 = AGND (Pin 1 CN_OUT)

Pin 03 = GunX1 (Pin 2 CN_OUT)

Pin 04 = GunY1 (Pin 3 CN_OUT)

Pin 05 = GunX2 (Pin 4 CN_OUT)

Pin 06 = GunY2 (Pin 5 CN_OUT)

White 15pin Amp

---------------

Pin 11 = +12V (Pin 2 CN_VCC)

Pin 15 = Gnd (Pin 1 CN_VCC and CN_OUT)

OldFoo · Post by **OldFoo** » Mon Mar 08, 2010 11:13 am

MaNiAc wrote:just done a gun conversion on my cab what connector you stuck on.?

on CN1 connector rear VTS :smt004

purplec wrote:In the process of doing the same, you will find the manual you need on the link below and a few others that you may need.

http://www.segaarcade.com/archive/mazeo ... spx#bottom

this is no universal naomi with VTS pcb... this is without vts

OldFoo · Post by **OldFoo** » Mon Mar 08, 2010 11:39 am

CN1 isnt used on naomi universal cab! as i asked the same question.

all manuals are based on woodies for usa market for all games havent seen even a confidencal mission manual for a naomi universal cab.

hope this helps.

OldFoo · Post by **OldFoo** » Tue Mar 09, 2010 6:41 am

thanks all.......

new question about connection cables of the platform of a maze ...

beyond the 2 white connectors ....

you notice a USB cable .... where it is needed in the tower?

There are other PCB with USB data? :smt010

the photo is taken from a nice guy. the platform is not mine ... perhaps :smt009

OldFoo · Post by **OldFoo** » Tue Mar 09, 2010 8:49 am

Another question......

What it does, the connector CN1 on PCB IC Bd Gun Sense? 3 pin (freq/gnd/***)

thanks