Wangan 2 on Outrun 2 setup?

[OldFoo]

I will soon have a Outrun 2 driving setup using the Chihiro Type 3, Scud dash, MIDI motor drive bd, etc.



Will this setup also be able to play Wangan Midnight Maximum Tune 2? Or do I need another steering wheel/motor driver PCB?



Thanks..!

[OldFoo]

I will soon have a Outrun 2 driving setup using the Chihiro Type 3, Scud dash, MIDI motor drive bd, etc.



Will this setup also be able to play Wangan Midnight Maximum Tune 2? Or do I need another steering wheel/motor driver PCB?



Thanks..!

Wangan will work with the steering wheel etc, but no feedback..

[OldFoo]

I believe Wangan 2 works with the same Namco steer board, V257 STR PCB as the System 246 drivers like Ridge Racer 5 and Wangan Midnight which work with a Atari/Midway/Happ style 2 wire feedback motor. Would be a bit of rewiring not to mention fitting the motor to the dash. Funny, I just bought a Wangan 2 GD ROM and will be doing that same conversion.

[OldFoo]

I will soon have a Outrun 2 driving setup using the Chihiro Type 3, Scud dash, MIDI motor drive bd, etc.



Will this setup also be able to play Wangan Midnight Maximum Tune 2? Or do I need another steering wheel/motor driver PCB?



Thanks..!

Wangan will work with the steering wheel etc, but no feedback..

Thanks. I will try this soon. let's see how bad it plays without force feedback

I believe Wangan 2 works with the same Namco steer board, V257 STR PCB as the System 246 drivers like Ridge Racer 5 and Wangan Midnight which work with a Atari/Midway/Happ style 2 wire feedback motor. Would be a bit of rewiring not to mention fitting the motor to the dash. Funny, I just bought a Wangan 2 GD ROM and will be doing that same conversion.

No such thing as coincedence



Hmm.. fitting a different motor to the dash.. that is a challenge. I guess in a two-wire setup the position of the steering wheel is determined based on the value of a potentiometer position? Sounds like a lot of work.. Or would it be feasible to mount an entire happ-style steering assembly+motor to the dash? I recently read about someone that actually mounted a G25 wheel in an Initial D dash. Required some metal work, though.

[OldFoo]

Yes, when I say 2 wire, I mean 2 wires to the motor and 3 to the pot (of course). I am actually working in the other direction, running an Outrun2 on a a cab wired with a Happ motor. Works fine, steering wheel is centered when you are going straight and I didn't need to move the pot at all. Not quite the same without feedback though. I am picking up a Super GT dash this weekend and will fit the motor in my dash (I already have the MIDI board). Good luck with your project!

[OldFoo]

I believe Wangan 2 works with the same Namco steer board, V257 STR PCB as the System 246 drivers like Ridge Racer 5 and Wangan Midnight which work with a Atari/Midway/Happ style 2 wire feedback motor. Would be a bit of rewiring not to mention fitting the motor to the dash. Funny, I just bought a Wangan 2 GD ROM and will be doing that same conversion.

Remember each Namco board needs it's own program rom present on there (surface mount)

[OldFoo]

Are they game specific? My Ridge Racer V and Wangan Midnight both run on the same 246 and STR PCB, I just change the DVD & security fob. Do you know if you would need a different ROM for Wangan 2/Maxi Tune? If so are there any files on these so you could burn one?

[OldFoo]

Are they game specific? My Ridge Racer V and Wangan Midnight both run on the same 246 and STR PCB, I just change the DVD & security fob. Do you know if you would need a different ROM for Wangan 2/Maxi Tune? If so are there any files on these so you could burn one?

Yes you need different eproms for maximum tune and also mario kart..



It's a surface mount rom as well..