Chihiro at home

OldFoo · Post by **OldFoo** » Wed Aug 25, 2010 12:04 am

as long as its 3k to 7k it should be fine.

OldFoo · Post by **OldFoo** » Wed Sep 01, 2010 6:49 am

Could you use the extra button connector on the Capcom I/O for the drive controls? I was under the impression I could only use the Sega model.

OldFoo · Post by **OldFoo** » Thu Sep 02, 2010 2:04 am

Just buy it from the Market Section.

If I was not so tight on budget right now it would probably be gone

http://www.sega-naomi.com/forum/viewtopic.php?t=4369

Bob Presutti

OldFoo · Post by **OldFoo** » Thu Sep 02, 2010 3:09 pm

SkiDog wrote:Just buy it from the Market Section.

If I was not so tight on budget right now it would probably be gone

http://www.sega-naomi.com/forum/viewtopic.php?t=4369

Bob Presutti

Yeah I noticed that and I talked to the seller already but can the Capcom I/O supply the analog driving controls? I swear I read somewhere that you could only use the Sega version.

OldFoo · Post by **OldFoo** » Thu Sep 02, 2010 3:13 pm

yeah Capcom IO only has the JAMMA hookups and the extra plug for the kick buttons Im not aware that the Capcom IO has the Analog harness, best bet is just get the JAMMA JVS IO with the Analog harness ready

OldFoo · Post by **OldFoo** » Fri Feb 04, 2011 11:30 pm

I've been thinking about doing the same thing for a while now, what pedals could be used?

What would OutRun play like using a hacked wheel without the force feedback?

OldFoo · Post by **OldFoo** » Tue Sep 20, 2011 9:11 am

purplec wrote:Ok So I have had a look at the IO controls on Initial D 3

So I think I know what to do with all the buttoins but its the steering that would have me stumped.

Any advice on this before I go start hacking

Cheers

purplec wrote:So

1,3,5 connect to the steering

7,9,11 conect to the acc

13,15,17 connect to the brake

all the above use pots I take it, would a dreamcast or similar console wheel use pots

Cheers

Hello

I'm very interesting about wheel conversion and begined myself some research in order to have own wheel (triforce and naomi at home)

about the first quote => i found the same diagrams and more for JVS I/O and all are same pinouts => no difficult to understand about

about the second quote => it's the same, I understand also but I'm just stuck with AVCC terms

AVCC = unknow term

AVGND = I suppose it's same as ground wire

-------------------------

actually some things miss for me

how i can wire correctly the sterring wheel (pinout 3 from RA26P)

i have the wheel but i need to know what i must have i need in addition in order to complete properly my arcade at home project

thanks for your help about

.

OldFoo · Post by **OldFoo** » Tue Sep 20, 2011 12:08 pm

take a look at this part

OldFoo · Post by **OldFoo** » Tue Sep 20, 2011 1:11 pm

zitoun wrote:

take a look at this part

thanks for your answer

i saw this diagram and never thought this part can be helpfull :p

however, I'm not really clue about and need some additional help

If I understand, basically, there are 3 wire. It is correct ?

again thanks for your help

OldFoo · Post by **OldFoo** » Tue Sep 20, 2011 2:01 pm

There are 3 x 3 wire. 3 on each pots

===> 38 = pin 1 analog I/O = Pin 3 Steering's pot

===> 40 = pin 3 analog I/O = Pin 2 steering's pot

===> 58 = pin 5 analog I/O = Pin 1 Steering's pot

And so on ...