Lost World Model 3 wiring

OldFoo · Post by **OldFoo** » Wed Nov 15, 2006 4:42 pm

Hello !

I could get a lost world model 3 pcb with guns, filterboard, gun pcb and the 12 sensor.

But the wiring loom is missing.

Does anybody have such a loom or know a merchant who sells it ?

I would like to run the pcb in my astro city cab (so i would make the wiring loom jamma compatible).

Greetings

RFK

OldFoo · Post by **OldFoo** » Thu Nov 16, 2006 9:39 am

The one on eBay?? haha yes I told the guy it is impossible to find the wiring looms, you'd have to make them.

OldFoo · Post by **OldFoo** » Thu Nov 16, 2006 10:36 am

Where is this auction?

Can't find it on the superb eBay search

OldFoo · Post by **OldFoo** » Thu Nov 16, 2006 1:42 pm

AndyGeezer wrote:The one on eBay?? haha yes I told the guy it is impossible to find the wiring looms, you'd have to make them.

Hi !

Ok, so do you have any information to make such a wiring loom ?

What about the 12 sensors around the monitor ?

Does it matter if my monitor is a little bit bigger (29 inch instead of the usual 25 inch) ?

What about the idea to buy a model 3 jamma loom (many merchants have them in stock) and modify it for the lost world pcb ?

And yes, it was an auction on ebay.co.uk.

Greetings

RFK

OldFoo · Post by **OldFoo** » Thu Nov 16, 2006 4:01 pm

You can download the Lost World manual.

http://www.suzo.co.uk/websites/suzo/mai ... MANUAL.pdf

It was a 29" monitor, not 25"

You can make the wiring, just need a lot of patience, and ideally you need to make the gun wiring looms RF shielded.

OldFoo · Post by **OldFoo** » Thu Nov 16, 2006 5:41 pm

Hello !

Thank you very much for the link.

So wish me luck with the wiring loom.

The game is so incredible. I remember the great crocodile jumping out of the water and attacking the players. Or the gigantic T Rex hunting down the players in a tech lab.

Or...and of course the shitting dino

...those were the days sega...those were the days my friend *sigh*

But ok, Virtua Fighter 5 and Afterburner Climax also rock.

Greetings

RFK

OldFoo · Post by **OldFoo** » Thu Nov 16, 2006 8:12 pm

If you like shooters, you should try Ghost Squad, that game rocks!

OldFoo · Post by **OldFoo** » Thu Nov 16, 2006 10:31 pm

Hi !

Thank you for the tip.

How much will a kit cost ?

And where can i get one ?

Greetings

RFK

OldFoo · Post by **OldFoo** » Fri Nov 17, 2006 8:28 am

The game is quite new, so you'd be looking in around ?4000 for the kit.

The Chihiro Type 3 mainboard is worth ?2000, as it can run games like Outrun 2 SP/Maximum Tune 1/2

OldFoo · Post by **OldFoo** » Mon Nov 27, 2006 7:08 pm

Hi again !

I have recieved the lost world kit and i have also printed out the lost world manual.

There are two sheets with the pinout information.

Voltage and rgb signal will be really no problem (i have made a wiring loom for house of the dead already, so im an not a noob

).

But now comes the different part: Could you explain how to wire up the guns and the sensor parts with the gun i/0 board and the model 3 filterboard ?

The gun i/o board also needs 12 and 5 volt if i am not wrong.

Greetings

RFK